Gender differences in cementless short stem total hip arthroplasty: significantly higher femoral lengthening in female patients.

Modern cementless short stems in total hip arthroplasty (THA) enable a precise reconstruction of the native pre-arthritic hip geometry. While gender differences have been reported for older generation straight hip stems, there are hardly reports regarding modern cementless short hip stems. Therefore, we aimed to evaluate the influence of gender differences in hip anatomy in cementless short stem THA. A total of 207 patients (109 females, 98 males) with unilateral THA and absence of contralateral joint space narrowing (Kellgren-Lawrence grade ≤ 2) were included. Acetabular height and offset as well as femoral height and offset were measured on pre- and 3-months-postoperative anteroposterior X-rays of the pelvis and compared to the contralateral hip. Additionally, implant position was evaluated on the postoperative radiograph. In male patients, the loss of acetabular offset was significantly greater than in females (p = 0.012), leading to a compensatory increase in femoral offset (p = 0.041). Femoral height discrepancy was significantly higher in females (p < 0.001), accounting for an increased global hip height discrepancy (p < 0.001). The mean acetabular anteversion was significantly greater in female patients (p < 0.001). Female patients are at higher risk of femoral lengthening in THA with a cementless short stem potentially caused by a further proximally conducted femoral neck osteotomy and show significantly higher cup anteversion angles. Therefore, surgeons should take special care to the level of neck resection and implant positioning in female patients.

The Effect of Cerclage Banding Distally to a Clamshell Fracture Pattern in Total Hip Arthroplasty-A Biomechanical Study.

OBJECTIVES: As currently there is no existing biomechanical work on the topic of interest, the aim of the current study was to investigate the effect of cerclage banding distally to an intraoperatively occurring proximal periprosthetic femoral clamshell fracture versus a non-fractured femur after total hip arthroplasty. METHODS: A diaphyseal anchoring stem was implanted in twenty paired human cadaveric femora, assigned to a treatment and a control group. In the treatment group, each specimen was fitted with a cerclage band placed 3 mm distally to a clamshell fracture, created with an extent of 40% of the anchoring length of the stem. The resulting fragment was not treated further. The contralateral specimens were left with the stems without further fracture creation or treatment. All constructs were tested under progressively increasing cyclic axial loading until failure. Relative bone-implant movements were monitored by motion tracking. RESULTS: Number of cycles and the corresponding load at stem loosening, defined as 1 mm displacement of the stem along the shaft axis, were 31,417 ± 8870 and 3641.7 ± 887 N in the control group, and 26,944 ± 11,706 and 3194.4 ± 1170.6 N in the treatment group, respectively, with no significant differences between them, p = 0.106. CONCLUSION: From a biomechanical perspective, cerclage banding distally to an intraoperative clamshell fracture with an extent of 40% of the anchoring length of the stem demonstrated comparable resistance against hip stem loosening versus a non-fractured femur. It may therefore represent a valid treatment option to restore the full axial stability of a diaphyseal anchoring stem. In addition, it may be considered to keep the medial wall fragment unfixed, thus saving operative time and minimizing associated risks.

A neck-sparing short stem shows significantly lower blood loss in total hip arthroplasty compared to a neck-resecting short stem.

Short stems are associated with a significantly lower blood loss (BL) compared to straight stems in total hip arthroplasty (THA). Different types of stems differ in design, fixation and level of femoral neck osteotomy. Therefore, we sought to evaluate the difference regarding the perioperative BL between two short stems with different designs in direct anterior approach (DAA). A total of 187 THA performed by a single surgeon were analysed. 107 patients received a neck-resecting (Group A) and 80 patients a neck-sparing short stem (Group B). Blood counts of the day before surgery and of two days after surgery were evaluated. Total blood volume and BL were calculated. Additionally, duration of surgery was analysed. The perioperative BL was significantly lower in Group B (451.4 ± 188.4 ml) compared to Group A (546.6 ± 232.7 ml; p = 0.002). The postoperative haematocrit (31.6 ± 3.7% vs. 30.4 ± 4.4%; p = 0.049) and haemoglobin-level (11.0 ± 1.3 g/dL vs. 10.4 ± 1.5 g/dL; p = 0.002) were significantly higher in Group B. Duration of surgery was significantly shorter in Group B (62.0 ± 11.4 min vs. 72.6 ± 21.8 min; p < 0.001). The use of a neck-sparing short stem leads to a significantly decreased BL compared to a neck-resecting short stem in DAA THA. A less extensively conducted capsular release necessary for optimal femoral exposition might lead to a lower perioperative BL and shorter durations of surgery.

Not all questions are created equal: the weight of the Oxford Knee Scores questions in a multicentric validation study.

BACKGROUND: The Oxford Knee Score (OKS) has been designed for patients with knee osteoarthritis and has a widespread use. It has 12 questions, with each question having the same weight for the overall score. Some authors have observed a significant ceiling effect, especially when distinguishing slight postoperative differences. We hypothesized that each questions' weight will depend significantly on the patient's sociodemographic data and lifestyle. METHODS: In this international multicentric prospective study, we included patients attending a specialist outpatient knee clinic. Each patient filled out 3 questionnaires: (a) demographic data and data pertaining to the OKS, (b) the standard OKS, and (c) the patient gave a mark on the weight of the importance of each question, using a 5-point Likert scale (G OKS). Linear regression models were used for the analysis. RESULTS: In total 203 patients (106 female and 97 male) with a mean age of 64.5 (±12.7) years and a mean body mass index (BMI) of 29.34 (±5.45) kg/m2 were included. The most important questions for the patients were the questions for pain, washing, night pain, stability, and walking stairs with a median of 5. In the regression models, age, gender, and driving ability were the most important factors for the weight of each of the question. CONCLUSION: The questions in the OKS differ significantly in weight for each patient, based on sociodemographic data, such as age, self-use of a car, and employment. With these differences, the Oxford Knee Score might be limited as an outcome measure. Adjustment of the OKS that incorporates the demographic differences into the final score might be useful if the ceiling effect is to be mitigated. LEVEL OF EVIDENCE: Level II prospective prognostic study.

The learning curve in robotic assisted knee arthroplasty is flattened by the presence of a surgeon experienced with robotic assisted surgery.

PURPOSE: The purpose of this study was to investigate the learning curve associated with robotic assisted knee arthroplasty (RAS KA). Therefore, the evaluation of the influence of an experienced surgeon on the overall team performance of three surgeons regarding the learning curve in RAS KA was investigated. It was hypothesized that the presence of an experienced surgeon flattens the learning curve and that there was no inflection point for the learning curve of the surgical team. METHODS: Fifty-five cases consisting of 31 total knee arthroplasties (TKA) and 24 unicompartmental arthroplasties (UKA) performed by three surgeons during 2021 were prospectively investigated. Single surgeon and team performance for operation time learning curve and inflection points were investigated using cumulative sum analysis (CUSUM). RESULTS: A downward trend line for individual surgeons and the team performance regarding the operation time learning curve was observed. No inflexion point was observed for the overall team performance regarding TKA and UKA. The surgeon that performed all cases with the assistance of the experienced surgeon had significantly shorter surgical times than the surgeon that only occasionally received assistance from the experienced surgeon (p = 0.004 TKA; p = 0.002 UKA). CONCLUSION: The presence of an experienced surgeon in robotically assisted knee arthroplasty can flatten the learning curve of the surgical team formerly unexperienced in robotic assisted systems. Manufacturers should provide expanded support during initial cases in centres without previous experience to robotic assisted knee arthroplasty. LEVEL OF EVIDENCE: III.

Cementless femoral stem revision in total hip arthroplasty: The periprosthetic clamshell fracture. A biomechanical investigation.

To biomechanically evaluate the stability of a diaphyseal anchored, cementless stem in presence of a proximal periprosthetic femoral medial wall defect compared to the stability of the same stem in an intact femur. Twenty-two paired human cadaveric femora were pairwise assigned either to a fracture group, featuring a proximal medial wall defect involving 40% of the stems medial anchorage distance, or a control group with native specimens. The specimens were tested under a monotonically increasing cyclic axial loading protocol. Load, cycles, and multiples of the respective body weight at implant loosening was measured. Mean initial stiffness was 2243.9 ± 467.9 N/mm for the intact group and 2190.1 ± 474.8 N/mm for the fracture group. Mean load to loosening in the intact group was 3210.5 ± 1073.2 N and 2543.6 ± 576.4 N in the fracture group, with statistical significance. Mean cycles to loosening in the intact group were 27104.9 ± 10731.7 and 20431.5 ± 5763.7 in the fracture group, with statistical significance. Mean multiples of the resulting body weight at loosening in the intact group was 548.3 ± 158.5% and 441.4 ± 104% in the fracture group, with statistical significance. A medial wall defect involving 40% of the medial anchorage distance significantly decreases the axial stability of a diaphyseal anchored stem. However, mechanical failure occurred beyond physiological stress. At loosening rates of about 4 multiples of the body weight in the fracture group, a "safe zone" remains of a 0.5-fold body weight for maximum loads and twofold body weights for average loads.

Periprosthetic Femoral Fractures in Cementless Short Versus Straight Stem Total Hip Arthroplasty: A Propensity Score Matched Analysis.

BACKGROUND: Recent studies indicate a decreased risk of periprosthetic femoral fractures (PFFs) in cementless total hip arthroplasty (THA) for short compared to straight stems. However, the results are still inconclusive. Therefore, we retrospectively investigated the rate of PFFs within the first year between cementless short and straight stem THA. METHODS: A 1:1 propensity score matching of 3,053 THAs was performed. Two groups including 1,147 short stem THAs implanted through a minimally invasive antero-lateral approach and 1,147 straight stem THAs implanted through a transgluteal Hardinge approach were matched. The rates of PFFs and fracture patterns were compared between both stem types. Risk factors for PFFs were analyzed by multivariate regression analyses. RESULTS: The overall rate of PFFs was 1.7% in short stem THA and 3.2% in straight stem THA (P = .015). Postoperatively detected Vancouver A fractures occurred significantly more often in straight stem THA (P = .002), while the occurrence Vancouver B fractures did not differ significantly (P = .563). The risk of PFFs was significantly increased for women in straight stem THA (Odds ratio (OR) 2.620; Confidence Interval (CI) 1.172-5.856; P = .019). Increasing age showed a significantly increased odds ratio in short stem (OR 1.103; CI 1.041-1.169, P < .001) and straight stem THA (OR 1.057; CI 1.014-1.101, P = .008). CONCLUSION: Short stem THA reduces Vancouver Type A PFFs in the trochanteric region compared to straight stem THA, while Vancouver Type B fractures are comparable. Increasing age is a significant risk factor for both stem types, while the risk for PFFs in women was only significantly increased in the straight stem group.

Impact of Anterior Malposition and Bone Cement Augmentation on the Fixation Strength of Cephalic Intramedullary Nail Head Elements.

Background and Objectives: Intramedullary nailing of trochanteric fractures can be challenging and sometimes the clinical situation does not allow perfect implant positioning. The aim of this study was (1) to compare in human cadaveric femoral heads the biomechanical competence of two recently launched cephalic implants inserted in either an ideal (centre-centre) or less-ideal anterior off-centre position, and (2) to investigate the effect of bone cement augmentation on their fixation strength in the less-ideal position. Materials and Methods: Fourty-two paired human cadaveric femoral heads were assigned for pairwise implantation using either a TFNA helical blade or a TFNA screw as head element, implanted in either centre-centre or 7 mm anterior off-centre position. Next, seven paired specimens implanted in the off-centre position were augmented with bone cement. As a result, six study groups were created as follows: group 1 with a centre-centre positioned helical blade, paired with group 2 featuring a centre-centre screw, group 3 with an off-centre positioned helical blade, paired with group 4 featuring an off-centre screw, and group 5 with an off-centre positioned augmented helical blade, paired with group 6 featuring an off-centre augmented screw. All specimens were tested until failure under progressively increasing cyclic loading. Results: Stiffness was not significantly different among the study groups (p = 0.388). Varus deformation was significantly higher in group 4 versus group 6 (p = 0.026). Femoral head rotation was significantly higher in group 4 versus group 3 (p = 0.034), significantly lower in group 2 versus group 4 (p = 0.005), and significantly higher in group 4 versus group 6 (p = 0.007). Cycles to clinically relevant failure were 14,919 ± 4763 in group 1, 10,824 ± 5396 in group 2, 10,900 ± 3285 in group 3, 1382 ± 2701 in group 4, 25,811 ± 19,107 in group 5 and 17,817 ± 11,924 in group 6. Significantly higher number of cycles to failure were indicated for group 1 versus group 2 (p = 0.021), group 3 versus group 4 (p = 0.007), and in group 6 versus group 4 (p = 0.010). Conclusions: From a biomechanical perspective, proper centre-centre implant positioning in the femoral head is of utmost importance. In cases when this is not achievable in a clinical setting, a helical blade is more forgiving in the less ideal (anterior) malposition when compared to a screw, the latter revealing unacceptable low resistance to femoral head rotation and early failure. Cement augmentation of both off-centre implanted helical blade and screw head elements increases their resistance against failure; however, this effect might be redundant for helical blades and is highly unpredictable for screws.

The race for the classification of proximal periprosthetic femoral fractures : Vancouver vs Unified Classification System (UCS) - a systematic review.

BACKGROUND: Periprosthetic femoral fractures (PFFs) represent a major cause for surgical revision after hip arthroplasty with detrimental consequences for patients. The Vancouver classification has been traditionally used since its introduction in 1995. The Unified Classification System (UCS) was described in 2014, to widen the spectrum by aiming for a more comprehensive approach. The UCS also aimed to replace the Vancouver classification by expanding the idea of the Vancouver classification to the whole musculoskeletal apparatus. After introduction of the UCS, the question was raised, whether the UCS found its place in the field of analysing PFFs. Therefore, this systematic review was performed to investigate, the use of the UCS compared to the established Vancouver classification. METHODS: Medline was searched for reports published between 1 January 2016 and 31 November 2020, without language restriction. Included were original articles, irrespective of the level of evidence and case reports reporting on a PFF and using either the Vancouver or the UCS to classify the fractures. Excluded were reviews and systematic reviews. RESULTS: One hundred forty-six studies were included in the analysis. UCS has not been used in a single registry study, giving a pooled cohort size of 3299 patients, compared to 59,178 patients in studies using the Vancouver classification. Since 2016, one study using UCS was published in a top journal, compared to 37 studies using the Vancouver classification (p=0.29). During the study period, the number of yearly publications remained stagnant (p=0.899). CONCLUSIONS: Despite valuable improvement and expansion of the latter UCS, to date, the Vancouver system clearly leads the field of classifying PFFs in the sense of the common use.

Is intrathoracic rib plate fixation advantageous over extrathoracic plating? A biomechanical cadaveric study.

BACKGROUND: The high morbidity following surgical interventions on the chest wall because of large incisions often prevents surgeons from operative rib fracture treatment. Minimally invasive approaches to the intrathoracic side of the rib could allow for smaller incisions with lower morbidity while maintaining stability of fixation. The aim of this study was to explore the biomechanical competence of intrathoracic versus extrathoracic plating in a human cadaveric rib fracture model and investigate the effect of plating using two versus three screws per fracture fragment. METHODS: Twenty pairs of fresh-frozen human cadaveric ribs from elderly female donors aged 82.4 ± 7.8 years were used. First, the stiffness of each native rib was calculated via nondestructive (2 N-5 N) biomechanical testing under two loading conditions: ramped two-point bending and combined ramped tensile bending with torsional loading. Second, the ribs were fractured under three-point bending with their intrathoracic side put under tensile stress. Third, specimens were assigned to four groups (n = 10) for either intrathoracic or extrathoracic plating with two or three screws per fragment. Following instrumentation, all ribs were dynamically tested over 400,000 cycles under combined sinusoidal tensile bending with torsional loading (2 N-5 N at 3 Hz). Finally, all specimens were destructively tested under ramped two-point bending. RESULTS: Following instrumentation and cyclic testing, significantly higher construct stiffness was observed for intrathoracic vs. extrathoracic plating under anatomical loading conditions (p ≤ 0.03). No significant differences were detected for implant subsidence after plating with two or three screws per fragment (p ≥ 0.20). CONCLUSION: This study demonstrates significantly higher construct stiffness following intrathoracic over extrathoracic plating, thus indicating superior plate support of the former. In the clinical context, using only two instead of three screws per fragment not only could maintain stability of fixation but also decrease surgery time and costs, and allow for smaller incisions with lower morbidity. LEVEL OF EVIDENCE: Therapeutic/Care Management; Level V.

Does Cement Augmentation of the Sacroiliac Screw Lead to Superior Biomechanical Results for Fixation of the Posterior Pelvic Ring? A Biomechanical Study.

Background and Objectives: The stability of the pelvic ring mainly depends on the integrity of its posterior part. Percutaneous sacroiliac (SI) screws are widely implanted as standard of care treatment. The main risk factors for their fixation failure are related to vertical shear or transforaminal sacral fractures. The aim of this study was to compare the biomechanical performance of fixations using one (Group 1) or two (Group 2) standard SI screws versus one SI screw with bone cement augmentation (Group 3). Materials and Methods: Unstable fractures of the pelvic ring (AO/OTA 61-C1.3, FFP IIc) were simulated in 21 artificial pelvises by means of vertical osteotomies in the ipsilateral anterior and posterior pelvic ring. A supra-acetabular external fixator was applied to address the anterior fracture. All specimens were tested under progressively increasing cyclic loading until failure, with monitoring by means of motion tracking. Fracture site displacement and cycles to failure were evaluated. Results: Fracture displacement after 500 cycles was lowest in Group 3 (0.76 cm [0.30] (median [interquartile range, IQR])) followed by Group 1 (1.42 cm, [0.21]) and Group 2 (1.42 cm [1.66]), with significant differences between Groups 1 and 3, p = 0.04. Fracture displacement after 1000 cycles was significantly lower in Group 3 (1.15 cm [0.37]) compared to both Group 1 (2.19 cm [2.39]) and Group 2 (2.23 cm [3.65]), p ≤ 0.04. Cycles to failure (Group 1: 3930 ± 890 (mean ± standard deviation), Group 2: 3676 ± 348, Group 3: 3764 ± 645) did not differ significantly between the groups, p = 0.79. Conclusions: In our biomechanical setup cement augmentation of one SI screw resulted in significantly less displacement compared to the use of one or two SI screws. However, the number of cycles to failure was not significantly different between the groups. Cement augmentation of one SI screw seems to be a useful treatment option for posterior pelvic ring fixation, especially in osteoporotic bone.

The morphology of the proximal femur in cementless short-stem total hip arthroplasty: No negative effect on offset reconstruction, leg length difference and implant positioning.

BACKGROUND: Correct reconstruction of hip offset (HO) and leg length are important for clinical-functional outcome and patient satisfaction in total hip arthroplasty (THA). The morphology of the proximal femur can pose a risk for increased leg length difference (LLD) in cementless straight-stem THA. We therefore wanted to evaluate, if this is also applicable in THA with a cementless meta-diaphyseal short stem. METHODS: In a retrospective study, 106 patients (index surgery 2014-2019) with unilateral THA and a morphologically healthy hip as a reference (Kellgren-Lawrence ≤ 1) were included. The same cementless short stem with meta-diaphyseal fixation and cementless press-fit cup was implanted. The proximal femur was rated by Dorr's classification, and subgroups were formed afterward. Measurements were carried out on preoperative and 3 months postoperative anterior-posterior radiographs of the pelvis. Kruskal-Wallis test, Fisher's exact test and binary logistic regression were performed to evaluate the influence of the anatomical shape on postoperative leg length difference and offset reconstruction. RESULTS: The Dorr type did not show any significance influence on LLD (p = 0.532), or postoperative difference in femoral offset (p = 0.243), acetabular offset (p = 0.106) and hip offset (p = 0.698). Stem alignment (p = 0.705) and canal fill indices (CFI I: p = 0.321; CFI II: p = 0.411; CFI III: p = 0.478) were also without significant differences. Logistic regression did not show any significant increased risk for a LLD ≥ 5 mm or ≥ 10 mm as well as HO ≥ 5 mm or ≥ 10 mm. CONCLUSION: Reconstruction of hip offset and postoperative leg length difference is not negatively influenced by Dorr type, canal flare index, cortical index and canal-to-calcar ratio in cementless short-stem THA. Implant positioning and canal fill are also not negatively affected by the anatomical shape of the proximal femur. LEVEL OF EVIDENCE: Level IV.

Is Anterior Plating Superior to the Bilateral Use of Retrograde Transpubic Screws for Treatment of Straddle Pelvic Ring Fractures? A Biomechanical Investigation.

BACKGROUND: Fractures of the four anterior pubic rami are described as "straddle fractures". The aim of this study was to compare biomechanical anterior plating (group 1) versus the bilateral use of retrograde transpubic screws (group 2). METHODS: A straddle fracture was simulated in 16 artificial pelvises. All specimens were tested under progressively increasing cyclic loading, with monitoring by means of motion tracking. RESULTS: Axial stiffness did not differ significantly between the groups, p = 0.88. Fracture displacement after 1000-4000 cycles was not significantly different between the groups, p ≥ 0.38; however, after 5000 cycles it was significantly less in the retrograde transpubic screw group compared to the anterior plating group, p = 0.04. No significantly different flexural rotations were detected between the groups, p ≥ 0.32. Moreover, no significant differences were detected between the groups with respect to their cycles to failure and failure loads, p = 0.14. CONCLUSION: The results of this biomechanical study reveal less fracture displacement in the retrograde transpubic screw group after long-term testing with no further significant difference between anterior plating and bilateral use of retrograde transpubic screws. While the open approach using anterior plating allows for better visualization of the fracture site and open reduction, the use of bilateral retrograde transpubic screws, splinting the fracture, presents a minimally invasive and biomechanically stable technique.

Minimally Invasive Approaching in Hip Surgery-An Anatomical Investigation of 20 Specimens.

Background and objectives: Based on the preparation of 20 formalin-fixed anatomical cadavers, the feasibility of the anterior, minimally invasive approach to the hip joint was investigated in each side of the body. The hypothesis of the study was that the Lateral Femoral Cutaneous Nerve can be spared under the use of this approach. Materials and Methods: The anterior approach to the hip was performed via an incision of 8 cm. The position of the nerve was noticed in relation to the skin incision, and the distance was measured in millimeters. The nerves main, gluteal and femoral trunk were distinguished and investigated for injury. Results: No injury of the main trunk was noticed. The average distance of the main trunk to the skin incision was 14.9 and 15.05 mm in the medial direction, respectively (p < 0.001). Injury of the gluteal branch has to be considered at an overall rate of 40%. Conclusions: The anterior, minimally invasive approach to the hip joint can be performed without injury of the Lateral Femoral Cutaneous Nerve.

Biomechanical Comparison of Five Fixation Techniques for Unstable Fragility Fractures of the Pelvic Ring.

BACKGROUND: Incidence of pelvic ring fractures has increased over the past four decades, especially after low-impact trauma-classified as fragility fractures of the pelvis (FFP). To date, there is a lack of biomechanical evidence for the superiority of one existing fixation techniques over another. An FFP type IIc was simulated in 50 artificial pelvises, assigned to 5 study groups: Sacroiliac (SI) screw, SI screw plus supra-acetabular external fixator, SI screw plus plate, SI screw plus retrograde transpubic screw, or S1/S2 ala-ilium screws. The specimens were tested under progressively increasing cyclic loading. Axial stiffness and cycles to failure were analysed. Displacement at the fracture sites was evaluated, having been continuously captured via motion tracking. RESULTS: Fixation with SI screw plus plate and SI screw plus retrograde transpubic screw led to higher stability than the other tested techniques. The S1/S2 ala-ilium screws were more stable than the SI screw or the SI screw plus external fixator. CONCLUSIONS: In cases with displaced fractures, open reduction and plate fixation provides the highest stability, whereas in cases where minimally invasive techniques are applicable, a retrograde transpubic screw or S1/S2 ala-ilium screws can be considered as successful alternative treatment options.

Obesity in short stem total hip arthroplasty using a minimally invasive supine anterolateral approach-a risk factor for short-term complications?

PURPOSE: Obesity is associated with increased risk for surgical complications in total hip arthroplasty (THA). The impact of obesity on short-term complication in minimally invasive (MIS) anterolateral approach is not well known. Therefore, this study was conducted to evaluate the early complications within the first 90 days after THA using a MIS anterolateral approach with a short-curved stem stratified by Body Mass Index (BMI). PATIENTS AND METHODS: A single centre consecutive series of 1052 hips in 982 patients (index surgery 2014-2019) with a short-curved stem and press fit cup implanted using a MIS anterolateral approach in supine position were screened for inclusion. Inclusion criteria were defined as end-stage primary osteoarthritis of the hip. Eventually, 878 implantations in 808 patients were included and stratified by body mass index (BMI). Peri-operative complications, within the first 90 days after surgery, were retrospectively evaluated. RESULTS: Severely obese patients (BMI ≥ 35 kg/m2) and morbidly obese patients (BMI ≥ 40 kg/m2) demonstrated a significantly increased operation time (p < 0.001) and a higher risk for general surgical complications (p = 0.015) (odds ratio (OR) = 4.365; OR = 4.985), periprosthetic joint infection (PJI) (p = 0.001) (OR = 21.687; OR = 57.653), and revision (OR = 8.793; OR = 20.708). CONCLUSION: The risk for early PJI and overall surgical complications in MIS anterolateral approach is significantly increased in severely and morbidly obese patients. This leads to a significantly higher risk for revision surgery after index surgery within the first 90 days. A BMI above 35 kg/m2 is the clear threshold for increased risk of PJI in MIS anterolateral THA with a short curved stem. As the surgical complications are comparable to other approaches, MIS anterolateral short stem THA is also feasible with increasing BMI.

Low rate of early periprosthetic fractures in cementless short-stem total hip arthroplasty using a minimally invasive anterolateral approach.

PURPOSE: Minimally invasive (MIS) approaches in combination with short stems have gained popularity in recent years in total hip arthroplasty (THA). A decreased risk for periprosthetic femoral fractures (PFFs) is reported for cementless short-stem THA, but in contrast to other approaches, the risk factors for PFFs for short-stem THA using MIS anterolateral approach in supine position are not described in literature. METHODS: A single-center consecutive series of 1052 hips in 982 patients, performed between 2014 and 2019 with a short curved stem and a press fit using an MIS anterolateral approach in supine position, was retrospectively screened for inclusion. Fourteen patients were lost to follow-up. Therefore, 1038 THAs in 968 patients were included. Risk factors for intra- and postoperative PFFs within 90 days were analyzed. We investigated for sex, age, body mass index (BMI), diagnosis, and laterality. RESULTS: In total, 18 PFFs (1.7%) occurred. Intraoperative fracture occurred in ten cases ( 0.9%), with another eight cases (0.8%) occurring postoperatively. Increased American Society of Anesthesiologists (ASA) Score was a significant risk factor for PFF (p = 0.026), whereas sex (p = 0.155), age (p = 0.161), BMI (p = 0.996), and laterality (p = 1.000) were not. Seven PFFs (0.7%) required revision arthroplasty. CONCLUSION: Cementless short-stem THA using the MIS anterolateral approach is a procedure with a low number of PFFs within 90 days from index surgery. Fracture rates are comparable to other MIS approaches, and comparable femoral short stems are used. Age, sex, and BMI were not identified as risk factors of PFF, while risk for PFF increased with ASA Score. LEVEL OF EVIDENCE: Level IV.

Screw-blade fixation systems for implant anchorage in the femoral head: Horizontal blade orientation provides superior stability.

OBJECTIVES: Despite continual improvement in the methods and devices used for treatment of proximal femoral fractures, unacceptably high failure rates remain. Novel screw-blade implant systems, combining a lag screw with a blade - the latter adding rotational stability to the femoral head - offer improvement of osseous purchase, especially in osteoporotic bone. The aim of this study was to compare biomechanically the head element (HE) anchorage of two screw-blade implant systems differing in blade orientation in the femoral head - vertical versus horizontal. METHODS: Twenty paired human cadaveric femoral heads were assigned to four groups (n = 10), implanted with either Rotationally Stable Screw-Anchor HE (RoSA-HE, vertical blade orientation) or Gamma3 Rotation Control Lag Screw (Gamma-RC, horizontal blade orientation) in center or off-center position, and biomechanically tested until failure under progressively increasing cyclic loading at 2 Hz. RESULTS: Cycles to failure and failure load were significantly higher for Gamma-RC versus RoSA-HE in center position and not significantly different between them in off-center position, p = 0.03 and p = 0.22, respectively. In center position, the progression of both rotation around implant axis and varus deformation over time demonstrated superiority of the implant with horizontal versus vertical blade orientation. Compared with center positioning, off-center implant placement led to a significant decrease in stiffness, cycles to failure and failure load for Gamma-RC, but not for RoSA-HE, p < 0.01 and p = 0.99, respectively. CONCLUSION: Horizontal blade orientation of screw-blade implant systems demonstrates better anchorage in the femoral head versus vertical blade orientation in center position. As the stability of the implant system with horizontal blade orientation drops sharply in off-center position, central insertion is its placement of choice.

Overdrilling increases the risk of screw perforation in locked plating of complex proximal humeral fractures - A biomechanical cadaveric study.

Locked plating of proximal humerus fractures (PHF) is associated with high failure rates (15-37%). Secondary screw perforation is a prominent mode of failure for PHF and typically requires reoperation. The anatomical fracture reduction is an essential factor to prevent fixation failure. However, recent studies indicate that the risk of secondary screw perforation may increase if the articular surface is perforated during predrilling of the screw boreholes (overdrilling). This study aimed to determine whether overdrilling increases the risk of secondary screw perforation in unstable PHF. Nine pairs of human cadaveric proximal humeri were osteotomized to simulate a malreduced and highly unstable 3-part fracture (AO/OTA 11 B1.1), followed by their assignment to two study groups for overdrilling or accurate predrilling in paired design, and fixation with a locking plate. Overdrilling was defined by drilling the calcar screw's boreholes through the articular surface. All humeri were cyclically loaded to screw perforation failure. Number of cycles to initial screw loosening and final perforation failure were analysed. The accurately predrilled group revealed a significantly higher number of cycles to both initial screw loosening (p < 0.01) and final screw perforation failure (p = 0.02), compared to the overdrilled one. This is the first study reporting that drilling to the correct depth significantly increases endurance until screw perforation failure during cyclic loading after locked plating in a highly unstable PHF model. Prevention of overdrilling the boreholes could help reduce failure rates of locked plating. Future work should investigate the prevalence and consequences of overdrilling in clinics.